Difference between revisions of "SWITCH-mikrotik"
From Fixme.ch
(→Config) |
(→Ports / Reseau) |
||
| Line 95: | Line 95: | ||
<td></td> | <td></td> | ||
</tr> | </tr> | ||
| − | <tr bgcolor= | + | <tr bgcolor=SlateGrey> |
<td>17</td> | <td>17</td> | ||
| − | <td>FIXME-NAT</td> | + | <td>reserved for FIXME-NAT</td> |
| − | <td></td> | + | <td>DON'T USE!</td> |
</tr> | </tr> | ||
| − | <tr bgcolor= | + | <tr bgcolor=LightSlateGrey> |
<td>18</td> | <td>18</td> | ||
| − | <td>FIXME-PUBLIC</td> | + | <td>reserved for FIXME-PUBLIC</td> |
| − | <td></td> | + | <td>DON'T USE!</td> |
</tr> | </tr> | ||
<tr bgcolor=SlateGrey> | <tr bgcolor=SlateGrey> | ||
Revision as of 10:54, 31 December 2023
SW-FIXME-MIKROTIK
Decoupage Public - NAT
On utilise pas de Vlan, mais on a deux bridges virtuelle qui font chacun des réseaux.
- 130: FIXME-NAT
- 135: FIXME-PUBLIC
Ports / Reseau
| Port | Réseau | Equipement |
| 1 | FIXME-NAT | Bellatrix PMI |
| 2 | FIXME-PUBLIC | Bellatrix |
| 3 | FIXME-NAT | Fablab link |
| 4 | FIXME-PUBLIC | Raspi Orbital |
| 5 | FIXME-NAT | Multifonction |
| 6 | FIXME-PUBLIC | RIPE NCC |
| 7 | FIXME-NAT | ATA |
| 8 | FIXME-PUBLIC | |
| 9 | FIXME-NAT | |
| 10 | FIXME-PUBLIC | |
| 11 | FIXME-NAT | |
| 12 | FIXME-PUBLIC | |
| 13 | FIXME-NAT | |
| 14 | FIXME-PUBLIC | |
| 15 | FIXME-NAT | |
| 16 | FIXME-PUBLIC | |
| 17 | reserved for FIXME-NAT | DON'T USE! |
| 18 | reserved for FIXME-PUBLIC | DON'T USE! |
| 19 | reserved for FIXME-NAT | DON'T USE! |
| 20 | reserved for FIXME-PUBLIC | DON'T USE! |
| 21 | reserved for FIXME-NAT | DON'T USE! |
| 22 | reserved for FIXME-PUBLIC | DON'T USE! |
| 23 | "TRUNK-NAT" | ROUTER-Edge |
| 24 | "TRUNK-PUBLIC" | ROUTER-Edge |
Config
/interface bridge add name=bridge4Nat add name=bridge4Public /interface bridge port add bridge=bridge4Nat interface=ether1 add bridge=bridge4Nat interface=ether3 add bridge=bridge4Nat interface=ether5 add bridge=bridge4Nat interface=ether7 add bridge=bridge4Nat interface=ether9 add bridge=bridge4Nat interface=ether11 add bridge=bridge4Nat interface=ether13 add bridge=bridge4Nat interface=ether15 add bridge=bridge4Nat interface=ether23 add bridge=bridge4Public interface=ether2 add bridge=bridge4Public interface=ether4 add bridge=bridge4Public interface=ether6 add bridge=bridge4Public interface=ether8 add bridge=bridge4Public interface=ether10 add bridge=bridge4Public interface=ether12 add bridge=bridge4Public interface=ether14 add bridge=bridge4Public interface=ether16 add bridge=bridge4Public interface=ether24 /ip address add address=192.168.251.xx/24 interface=bridge4Public
Pour controler:
/interface bridge print /interface bridge print detail
Reference:
