Sandbox - Revision history

Rorist at 13:22, 31 July 2015

2015-07-31T13:22:29Z

Rorist at 16:48, 6 October 2014

2014-10-06T16:48:55Z

Rorist at 16:37, 6 October 2014

2014-10-06T16:37:39Z

Sasha at 21:47, 24 February 2014

2014-02-24T21:47:57Z

Corecode at 18:34, 25 September 2011

2011-09-25T18:34:08Z

Admin at 08:38, 1 September 2011

2011-09-01T08:38:15Z

Admin at 08:36, 1 September 2011

2011-09-01T08:36:39Z

Admin at 08:35, 1 September 2011

2011-09-01T08:35:30Z

Admin at 08:14, 1 September 2011

2011-09-01T08:14:50Z

Admin: Created page with "test test test"

2011-09-01T08:13:28Z

Created page with "test test test"

New page

test test test

← Older revision		Revision as of 13:22, 31 July 2015
Line 1:		Line 1:
		+	<syntaxhighlight lang="python">
		+	import prout
		+	print 'salut'
		+	prout.test()
		+	</syntaxhighlight>
		+
	<math>		<math>
	f(x) = \sum_{n=0}^\infty a_n x^n		f(x) = \sum_{n=0}^\infty a_n x^n

@@ Line 1: / Line 1: @@
 <math>
-  \operatorname{erfc}(x) =
+f(x) = \sum_{n=0}^\infty a_n x^n
-  \frac{2}{\sqrt{\pi}} \int_x^{\infty} e^{-t^2}\,dt =
-  \frac{e^{-x^2}}{x\sqrt{\pi}}\sum_{n=0}^\infty (-1)^n \frac{(2n)!}{n!(2x)^{2n}}
 </math>

← Older revision		Revision as of 16:37, 6 October 2014
Line 1:		Line 1:
		+	<math>
		+	\operatorname{erfc}(x) =
		+	\frac{2}{\sqrt{\pi}} \int_x^{\infty} e^{-t^2}\,dt =
		+	\frac{e^{-x^2}}{x\sqrt{\pi}}\sum_{n=0}^\infty (-1)^n \frac{(2n)!}{n!(2x)^{2n}}
		+	</math>
		+
	# '''Configure your desired print parameters'''. The print parameters will depend on what you are printing and the quality that you're looking for. Here are some guidelines:		# '''Configure your desired print parameters'''. The print parameters will depend on what you are printing and the quality that you're looking for. Here are some guidelines:
	<div class="toccolours mw-collapsible mw-collapsed" style="width:800px">		<div class="toccolours mw-collapsible mw-collapsed" style="width:800px">

@@ Line 1: / Line 1: @@
-== test2 ==
+# '''Configure your desired print parameters'''. The print parameters will depend on what you are printing and the quality that you're looking for. Here are some guidelines:
+<div class="toccolours mw-collapsible mw-collapsed" style="width:800px">
-test test test <ref name="ref1">content of ref1</ref>
+The print parameters will depend on what you are printing and the quality that you're looking for. Here are some guidelines:
-test test test <ref name="ref1">bullshit</ref>
+<div class="mw-collapsible-content">
-test test test <ref name="ref2">content of ref2</ref>
+## '''Layer height''': the Ultimaker can print between 0.1mm and 0.25mm. 0.1mm should only be used for high precision, high detail prints; 0.15mm should be used for normal prints; 0.2-0.25mm should be used for fast prints where you don't mind the quality (e.g. holder, internal component, etc).
-test test test <ref name="ref3">content of ref3 [http://www.example.com link title]</ref>
+## '''Shell thickness''': this value should be a multiple of 0.4mm (the width of the nozzle). With 0.4mm you'll get 1 solid layer, with 0.8mm you'll get 2 solid layers, etc. 0.8mm is fine for most prints.
+## '''Enable retraction''': this retracts the filament when the nozzle moves from one area to another whilst not printing. It is best to leave this enabled.
-<references />
+## '''Bottom/top thickness''': the bottom and top thickness of the solid layer. This value should be a multiple of the layer height - a value between 0.2mm and 1mm is best for most prints, with 1mm used for very delicate models.

← Older revision		Revision as of 18:34, 25 September 2011
Line 1:		Line 1:
		+	== test2 ==
		+
	test test test <ref name="ref1">content of ref1</ref>		test test test <ref name="ref1">content of ref1</ref>
	test test test <ref name="ref1">bullshit</ref>		test test test <ref name="ref1">bullshit</ref>

← Older revision		Revision as of 08:14, 1 September 2011
Line 1:		Line 1:
	test test test		test test test
		+
		+	{{ref\|name=test prout}}
		+
		+	{{references}}