Difference between revisions of "Extension Explorer 16"

From Fixme.ch
Jump to: navigation, search
(→‎Description)
(→‎BOM - Bill of Material)
Line 224: Line 224:
  
 
== LED DISPLAY FIXME ==
 
== LED DISPLAY FIXME ==
 +
 +
{| class="BOM - Feux tricolor Part"
 +
|+ BOM for the Feux Tricolor
 +
|-
 +
! scope="col" | Designation
 +
! scope="col" | Nb de composants
 +
! scope="col" | Fournisseur
 +
! scope="col" | Référence
 +
! scope="col" | Prix
 +
|-
 +
| MULTI LEDS (5 led par boitier)
 +
| 21
 +
| Digikey
 +
| MEC1-160-02-S-D-A or MEC1-160-02-F-DEM2
 +
| 9.3 $/pieces
 +
|-
 +
|
 +
|-
 +
 +
|-
 +
 +
|-
 +
 +
|-
 +
 +
|-
 +
 +
|-
 +
 +
|-
 +
 +
|-
 +
 +
|-
 +
 +
|-
 +
 +
|}
  
 
A venir
 
A venir

Revision as of 11:51, 30 October 2015

Description

In French: Création d'une carte d'extension pour la carte Explorer (PROJET: Carte Explorer 16 & Exos sur les uC).

  • V1: un montage permettra de simuler un carrefour routier, composer de 4 feux (RGB)
  • V2: montage permettant d'allumer séquentiellement des leds pour afficher le nom de FIXME


in English: creation of one extansion board for the Explorer Board (see the links above)

  • V1: assembly will allow to simulate a crossroad (4 fires (RGB))
  • V2: assembly allowing to display sequentially the leds to screen FIXME

Digram - Schematic

Cross Light Part

  • Schema Feux Tricolores - Kicad

  • bloc H1 - General - Orcad

  • bloc H2 - Cross Light part - Orcad

LEDS DISPLAY FIXME

  • Fixme Display - lettre F - Orcad

  • Fixme Display - lettre I - Orcad

Part Calculation of Electronics Digram

LED's for crossroad

  • the datasheet of the DSP implemented on the Explorer Board 16 (see pages 1 & 273) indicates that :
    • output current of I/O : I = 10mA
    • voltage I/O : VDD = 3.3V
  • the datasheet of the red LED (see pages 3) indicates that :
    • conduction voltage : ULR = VF = 1.8V
    • average current : I = 20mA
  • the datasheet of the orange LED (see pages 3 / 4 / 5) indicates that :
    • conduction voltage : ULO = VF = 1.9V
    • average current : I = 30mA
  • the datasheet of the green LED (see pages 3 / 4 / 5) indicates that :
    • conduction voltage : ULG = VF = 2.2V
    • average current : I = 30mA

Formula

  • calculation of resistance R_LED_R :

R_{LED_R}=\frac{U_r}{I}=\frac{V_{DD}-U_{LR}}{I}=\frac{3.3V-1.8V}{10mA} = 150 ohm

  • power dispersed by the resistance P_R_LED_R :

P_{R_{LED_R}}=\frac{R_{LED_R}^2}{I}=\frac{150^{2}}{10mA} = 15 mW

  • calculation of resistance R_LED_O :

R_{LED_O}=\frac{U_r}{I}=\frac{V_{DD}-U_{LO}}{I}=\frac{3.3V-1.9V}{10mA} = 140 ohm

  • power dispersed by the resistance P_R_LED_O :

P_{R_{LED_O}}=\frac{R_{LED_O}^2}{I}=\frac{140^{2}}{10mA} = 14 mW

  • calculation of resistance R_LED_G :

R_{LED_G}=\frac{U_r}{I}=\frac{V_{DD} - U_{LG}}{I}=\frac{3.3V-2.2V}{10mA} = 110 ohm

  • power dispersed by the resistance P_R_LED_G :

P_{R_{LED_G}}=\frac{R_{LED_G}^2}{I}=\frac{110^{2}}{10mA} = 11 mW

Switch for crossroad

  • the datasheet of the DSP implemented on the Explorer Board 16 (see pages 1, 278, 279) indicates that :
    • output current of I/O : I_output = 10mA
    • input current of I/O : I_output max = 5mA
    • voltage I/O : VDD = 3.3V
    • leakage current of I/O : 2uA
    • low state ('0') in voltage : 0,2 * VDD

Formula

  • voltage seens by the input of uC when it's a low state VDD_low :

VDD_{low} = VDD \cdot 0.2 = 3.3 \cdot 0.2 = 0.66 V

  • Resitor seens by the input of uC when it's a low state RIN_low :

RIN_{low} = \frac{VDD_{low}}{I_L} = \frac{0.66}{2u} = 330 kohms

  • Resitor Pull-Up MAX :

R_{Pull-Up_{max}} = \frac{VDD - VDD_{low}}{I_L} = \frac{3.3 - 0.66}{2u} = 1.32 Mohms

Remark : the resistor must be more less that the R_PULL-UP_max - usually, the value of 10kohm is using for the resistor pull-up.

  • Current using when the switch is closed

I_{R_{Pull-Up}} = \frac{VDD - VDD_{low}}{R_{Pull-up}} = \frac{3.3 - 0.66}{10k} = 264 uA

  • power dispersed by the resistance push-pull when the switch is actived

P_{R_{Pull-Up}} = (VDD - VDD_{low}) \cdot I_{R_{Pull-Up}} = (3.3V - 0.66V)\cdot 262uA = 696.96 uW

LEDS For DSIPLAY FIXME

In French : pour cette partie du projet, le choix s'est porté sur des multi leds de type L-132CB, le but est que tous les segments verticaux s'allument en meme temps et tous les leds horizontales s'allume une après l'autre.

IN English: For this part of the project, the choice was carried on the multi LED L-132CB, the goal is that all vertical segment display in same time ans the horizontal leds display one after the others

  • U_LED = 2V
  • I_LED = 20mA

Layout

  • Extension Explorer 16 - cross fire - PCB Feux Tricolores - Kicad

  • H1 Cross Light - Layout - Orcad

BOM - Bill of Material

Cross Fire Part

BOM for the Feux Tricolor
Designation Nb de composants Fournisseur Référence Prix
Led Rouge 5mm 4 Farnell 2112111 0.307 CHFrs /pieces
Led Rouge SMD (option) 4 Farnell 8554641 0.0982 CHFrs /5pieces
Led Orange 5mm 4 Farnell 1003212 0.257 CHFrs /pieces
Led Orange SMD (option) 4 Farnell 8554552 0.537 CHFrs /5pieces
Led Verte 5mm 4 Farnell 2217954 0.368 CHFrs /pieces
Led Verte SMD (option) 4 Farnell 8554609 0.326 CHFrs /5pieces
Resistance SMD 110 ohm 100mW 4 Farnell 2351021 0.01 CHFrs /pieces
Resistance SMD 140 ohm 100mW 4 Farnell 2351049 0.01 CHFrs /pieces
Resistance SMD 150 ohm 100mW 4 Farnell 9332596 0.0734 CHFrs / 50pieces
Resistance SMD 10kohm 100mW 4 Farnell 9332391 0.082 CHFrs / 50pieces
Commutateur Tactile 1 Farnell 1555985 0.155 CHFrs /pieces
Connecteur 120pin 1 Digikey MEC1-160-02-S-D-A or MEC1-160-02-F-DEM2 9.3 $/pieces

LED DISPLAY FIXME

BOM for the Feux Tricolor
Designation Nb de composants Fournisseur Référence Prix
MULTI LEDS (5 led par boitier) 21 Digikey MEC1-160-02-S-D-A or MEC1-160-02-F-DEM2 9.3 $/pieces

A venir

Assembly

  • montage en VerroBoard Feux Tricolores

Tests

  • Test Feux Tricolores -> feux rouges

  • Test Feux Tricolores -> feux verts

Modification

Documentation

PDF FILE

required links

Contributor

Retrieved from "https://fixme.ch/w/index.php?title=Extension_Explorer_16&oldid=10690"