Difference between revisions of "Proxmark3"
From Fixme.ch
(Created page with "== Information == * http://www.proxmark.org/proxmark * http://code.google.com/p/proxmark3/wiki/Compiling == Flash the Proxmark using a BusPirate == * Get OpenOCD http://sourcefo...") |
(→Information) |
||
(14 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
+ | __TOC__ | ||
== Information == | == Information == | ||
* http://www.proxmark.org/proxmark | * http://www.proxmark.org/proxmark | ||
* http://code.google.com/p/proxmark3/wiki/Compiling | * http://code.google.com/p/proxmark3/wiki/Compiling | ||
+ | * DIY hf antenna | ||
+ | ** https://code.google.com/p/proxmark3/wiki/Antennas | ||
+ | ** http://www.proxmark.org/files/Documents/Antennas/How%20to%20design%20a%2013.56%20MHz%20customized%20tag%20antenna.pdf | ||
+ | * https://www.brmlab.cz/project/freakcard | ||
− | == | + | == Proxmark 3 client == |
− | * | + | * Build the client/bootloader: |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
sudo apt-get install build-essential libreadline5 libreadline-dev libusb-0.1-4 libusb-dev libqt4-dev perl pkg-config | sudo apt-get install build-essential libreadline5 libreadline-dev libusb-0.1-4 libusb-dev libqt4-dev perl pkg-config | ||
Line 27: | Line 26: | ||
./client/proxmark3 | ./client/proxmark3 | ||
* Use it as Mifare emulator, https://code.google.com/p/proxmark3/wiki/Mifare | * Use it as Mifare emulator, https://code.google.com/p/proxmark3/wiki/Mifare | ||
+ | |||
+ | == Flash the Proxmark using a BusPirate == | ||
+ | * Get OpenOCD and compile it for the BusPirate | ||
+ | git clone git://openocd.git.sourceforge.net/gitroot/openocd/openocd | ||
+ | cd openocd | ||
+ | ./configure --enable-buspirate --enable-maintainer-mode --disable-werror --disable-shared | ||
+ | make && sudo make install | ||
+ | * Build the proxmark roms (bootrom and fullimage), see above | ||
+ | * Wire the BusPirate to the Proxmark3 | ||
+ | ** Pin 20 is GND and the the closest to the center of the board | ||
+ | ** Connect GND, TDO, TMS, TDI, TCK using these pinouts, respectively p3 and buspirate | ||
+ | [[Image:Ulink_arm20pin_proxmark.gif|x200px]] | ||
+ | [[Image:buspirate_serial_pinout_connections_by_sparkfun-800x392.png|x200px]] | ||
+ | * Connect to the bus pirate | ||
+ | wget https://raw.githubusercontent.com/hewittc/proxmark3lcd/master/tools/at91sam7s512-buspirate.cfg | ||
+ | openocd -f at91sam7s512-buspirate.cfg | ||
+ | * Connect the p3 by USB | ||
+ | * Connect to openocd and flash | ||
+ | nc localhost 4444 | ||
+ | > halt | ||
+ | > flash erase_sector 0 0 15 | ||
+ | > flash erase_sector 1 0 15 | ||
+ | > flash write_image /full/path/to/armsrc/obj/fullimage.elf | ||
+ | > flash write_image /full/path/to/bootrom/obj/bootrom.elf | ||
+ | * Wait and enjoy the P3 | ||
+ | |||
+ | * References | ||
+ | ** http://umeahackerspace.se/2013/03/21/bus-pirate-saves-the-day-proxmark3-jtag-flashing/ | ||
+ | ** http://michaldemin.wordpress.com/2010/02/27/how-to-buspirate-and-openocd/ | ||
+ | |||
+ | == See Also == | ||
+ | * [[Bus_pirate]] |
Latest revision as of 15:15, 29 April 2014
Information
- http://www.proxmark.org/proxmark
- http://code.google.com/p/proxmark3/wiki/Compiling
- DIY hf antenna
- https://www.brmlab.cz/project/freakcard
Proxmark 3 client
- Build the client/bootloader:
sudo apt-get install build-essential libreadline5 libreadline-dev libusb-0.1-4 libusb-dev libqt4-dev perl pkg-config
cd /tmp wget http://sourceforge.net/p/devkitpro/perlupdaters/ci/master/tree/devkitARMupdate.pl?format=raw -o devkit.pl chmod devkit.pl ./devkit.pl export DEVKITPRO=~/devkitPro export DEVKITARM=${DEVKITPRO}/devkitARM export PATH=$DEVKITARM/bin/:${PATH}
svn co http://proxmark3.googlecode.com/svn/trunk proxmark3-read-only cd proxmark3-read-only make
- Plug the Proxmark
./client/proxmark3
- Use it as Mifare emulator, https://code.google.com/p/proxmark3/wiki/Mifare
Flash the Proxmark using a BusPirate
- Get OpenOCD and compile it for the BusPirate
git clone git://openocd.git.sourceforge.net/gitroot/openocd/openocd cd openocd ./configure --enable-buspirate --enable-maintainer-mode --disable-werror --disable-shared make && sudo make install
- Build the proxmark roms (bootrom and fullimage), see above
- Wire the BusPirate to the Proxmark3
- Pin 20 is GND and the the closest to the center of the board
- Connect GND, TDO, TMS, TDI, TCK using these pinouts, respectively p3 and buspirate
- Connect to the bus pirate
wget https://raw.githubusercontent.com/hewittc/proxmark3lcd/master/tools/at91sam7s512-buspirate.cfg openocd -f at91sam7s512-buspirate.cfg
- Connect the p3 by USB
- Connect to openocd and flash
nc localhost 4444 > halt > flash erase_sector 0 0 15 > flash erase_sector 1 0 15 > flash write_image /full/path/to/armsrc/obj/fullimage.elf > flash write_image /full/path/to/bootrom/obj/bootrom.elf
- Wait and enjoy the P3
- References