Difference between revisions of "SWITCH-mikrotik"
From Fixme.ch
(→Config) |
(→Config) |
||
| Line 173: | Line 173: | ||
/ip address add address=192.168.130.11/24 interface=bridge4Public | /ip address add address=192.168.130.11/24 interface=bridge4Public | ||
| + | |||
| + | /interface ethernet | ||
| + | |||
| + | disable ether17 | ||
| + | disable ether18 | ||
| + | disable ether19 | ||
| + | disable ether20 | ||
| + | disable ether21 | ||
| + | disable ether22 | ||
| + | |||
</pre> | </pre> | ||
Revision as of 14:31, 2 January 2024
SW-FIXME-MIKROTIK
Decoupage Public - NAT
On utilise pas de Vlan, mais on a deux bridges virtuelle qui font chacun des réseaux.
- 130: FIXME-NAT
- 135: FIXME-PUBLIC
Ports / Reseau
| Port | Réseau | Equipement |
| 1 | FIXME-NAT | Bellatrix PMI |
| 2 | FIXME-PUBLIC | Bellatrix |
| 3 | FIXME-NAT | Fablab link |
| 4 | FIXME-PUBLIC | Raspi Orbital |
| 5 | FIXME-NAT | Multifonction |
| 6 | FIXME-PUBLIC | RIPE NCC |
| 7 | FIXME-NAT | ATA |
| 8 | FIXME-PUBLIC | |
| 9 | FIXME-NAT | |
| 10 | FIXME-PUBLIC | |
| 11 | FIXME-NAT | |
| 12 | FIXME-PUBLIC | |
| 13 | FIXME-NAT | |
| 14 | FIXME-PUBLIC | |
| 15 | FIXME-NAT | |
| 16 | FIXME-PUBLIC | |
| 17 | reserved for FIXME-NAT | DON'T USE! |
| 18 | reserved for FIXME-PUBLIC | DON'T USE! |
| 19 | reserved for FIXME-NAT | DON'T USE! |
| 20 | reserved for FIXME-PUBLIC | DON'T USE! |
| 21 | reserved for FIXME-NAT | DON'T USE! |
| 22 | reserved for FIXME-PUBLIC | DON'T USE! |
| 23 | "TRUNK-NAT" | ROUTER-Edge |
| 24 | "TRUNK-PUBLIC" | ROUTER-Edge |
Config
/user set 0 password="***********" /system identity set name=SW-FIXME-MIKROTIK /interface bridge add name=bridge4Nat add name=bridge4Public /interface bridge port add bridge=bridge4Nat interface=ether1 add bridge=bridge4Nat interface=ether3 add bridge=bridge4Nat interface=ether5 add bridge=bridge4Nat interface=ether7 add bridge=bridge4Nat interface=ether9 add bridge=bridge4Nat interface=ether11 add bridge=bridge4Nat interface=ether13 add bridge=bridge4Nat interface=ether15 add bridge=bridge4Nat interface=ether23 add bridge=bridge4Public interface=ether2 add bridge=bridge4Public interface=ether4 add bridge=bridge4Public interface=ether6 add bridge=bridge4Public interface=ether8 add bridge=bridge4Public interface=ether10 add bridge=bridge4Public interface=ether12 add bridge=bridge4Public interface=ether14 add bridge=bridge4Public interface=ether16 add bridge=bridge4Public interface=ether24 /ip address add address=192.168.130.11/24 interface=bridge4Public /interface ethernet disable ether17 disable ether18 disable ether19 disable ether20 disable ether21 disable ether22
Pour controler:
/interface bridge print /interface bridge print detail
Et eventuellement:
/user set 0 name = swadmin (si on veut changer le nom de l'admin)
Reference:
