Difference between revisions of "SWITCH-mikrotik"
(→Ports / VLAN) |
(→Ports / Reseau) |
||
| Line 127: | Line 127: | ||
<tr bgcolor=IndianRed> | <tr bgcolor=IndianRed> | ||
<td>23</td> | <td>23</td> | ||
| − | <td>TRUNK-NAT</td> | + | <td>"TRUNK-NAT"</td> |
| − | <td> | + | <td>[[ROUTER-Edge]]</td> |
</tr> | </tr> | ||
<tr bgcolor=LightCoral> | <tr bgcolor=LightCoral> | ||
<td>24</td> | <td>24</td> | ||
| − | <td>TRUNK-PUBLIC</td> | + | <td>"TRUNK-PUBLIC"</td> |
| − | <td> | + | <td>[[ROUTER-Edge]]</td> |
</tr> | </tr> | ||
</table> | </table> | ||
Revision as of 00:34, 23 December 2023
SW-FIXME-MIKROTIK
Decoupage Public - NAT
On utilise pas de Vlan, mais on a deux bridges virtuelle qui font chacun des réseaux.
- 130: FIXME-NAT
- 135: FIXME-PUBLIC
Ports / Reseau
| Port | Réseau | Equipement |
| 1 | FIXME-NAT | Bellatrix PMI |
| 2 | FIXME-PUBLIC | Bellatrix |
| 3 | FIXME-NAT | Fablab link |
| 4 | FIXME-PUBLIC | Raspi Orbital |
| 5 | FIXME-NAT | Multifonction |
| 6 | FIXME-PUBLIC | RIPE NCC |
| 7 | FIXME-NAT | ATA |
| 8 | FIXME-PUBLIC | |
| 9 | FIXME-NAT | |
| 10 | FIXME-PUBLIC | |
| 11 | FIXME-NAT | |
| 12 | FIXME-PUBLIC | |
| 13 | FIXME-NAT | |
| 14 | FIXME-PUBLIC | |
| 15 | FIXME-NAT | |
| 16 | FIXME-PUBLIC | |
| 17 | FIXME-NAT | |
| 18 | FIXME-PUBLIC | |
| 19 | reserved for FIXME-NAT | DON'T USE! |
| 20 | reserved for FIXME-PUBLIC | DON'T USE! |
| 21 | reserved for FIXME-NAT | DON'T USE! |
| 22 | reserved for FIXME-PUBLIC | DON'T USE! |
| 23 | "TRUNK-NAT" | ROUTER-Edge |
| 24 | "TRUNK-PUBLIC" | ROUTER-Edge |
Config
work in progress...
/interface vlan
add name=FIXME-NAT vlan-id=130 interface=ether23 (ne pas executer car a du être mis disable)
add name=FIXME-PUBLIC vlan-id=135 interface=ether24 (ne pas executer car a du être mis disable)
(/interface vlan print)
(/interface vlan print detail)
/interface bridge
add name=bridge4Nat
add name=bridge4Public
/interface bridge port
add bridge=bridge4Nat interface=FIXME-NAT (ne pas executer car a du être mis disable)
add bridge=bridge4Public interface=FIXME-PUBLIC (ne pas executer car a du être mis disable)
add bridge=bridge4Nat interface=ether1 (pvid=130)
add bridge=bridge4Nat interface=ether3
add bridge=bridge4Nat interface=ether5
add bridge=bridge4Nat interface=ether7
add bridge=bridge4Nat interface=ether9
add bridge=bridge4Nat interface=ether11
add bridge=bridge4Nat interface=ether13
add bridge=bridge4Nat interface=ether15
add bridge=bridge4Nat interface=ether17
add bridge=bridge4Public interface=ether2
add bridge=bridge4Public interface=ether4
add bridge=bridge4Public interface=ether6
add bridge=bridge4Public interface=ether8
add bridge=bridge4Public interface=ether10
add bridge=bridge4Public interface=ether12
add bridge=bridge4Public interface=ether14
add bridge=bridge4Public interface=ether16
add bridge=bridge4Public interface=ether18
(/interface bridge print)
(/interface bridge print detail)
((/ip address add address=192.168.1.1/24 interface=bridge1))
Reference:
