Difference between revisions of "Nighthawk250"
From Fixme.ch
(→Current setup) |
(→Upgrade planning) |
||
| Line 26: | Line 26: | ||
** DYS BE1806 2300KV http://www.banggood.com/DYS-BE1806-2300KV-Brushless-Motor-2-3S-for-Mini-Multicopters-p-933192.html | ** DYS BE1806 2300KV http://www.banggood.com/DYS-BE1806-2300KV-Brushless-Motor-2-3S-for-Mini-Multicopters-p-933192.html | ||
** 18g 88.8W http://fpvracing.ch/en/motors/62-emax-mt1806-2280kv-cw.html | ** 18g 88.8W http://fpvracing.ch/en/motors/62-emax-mt1806-2280kv-cw.html | ||
| − | * | + | * better frame |
| + | ** expensive 150$ http://www.minihquad.com/frames/blackout-mini-h-quad/ | ||
| + | ** cheap 20$ http://www.banggood.com/ZMR250-H250-250mm-Fiberglass-Mini-Quadcopter-Multicopter-Frame-Kit-p-933189.html | ||
* Better FPV antennas, stock are shitty with Skyzone kit (according to comments on HK) | * Better FPV antennas, stock are shitty with Skyzone kit (according to comments on HK) | ||
Revision as of 12:03, 28 July 2015
- Building a FPV Drone
Contents
Current setup
- Power calculator
- Frame: HobbyKing Spec Class 250fpv
- Motor: 4.4A max, 2-3s lipo, max 49W
- ESC: Afro 12A SimonK (2-4s lipo), BEC: 0.5A Linear 5.0v
- Props: Gemfan 5030
- FCU: CC3D Atom 4.8-15V 70mA
- Batteries
- 11.1V 3S 1800mAh 20C
- 11.1V 3S 1000mAh 20C
- 11.1V 3S 2200mAh 30C
- 14.8V 4S 1800mAh 25C (non usable with these motors)
- FPV
- FPV Camera: 1/3 Sony CCD 7-13V (3S) current 70mA
- FPV Transmitter: 7-24V 190mA manual -> FR1 CH8
- Video Receiver: current 12V 200mA
- Video "goggles"
- Weight:
- Theorical weight: ~415g
- Calculated weight: 560g
Upgrade planning
- More powerfull motors !
- better frame
- Better FPV antennas, stock are shitty with Skyzone kit (according to comments on HK)
Assembly
Frame
- Basic assembly guide: https://www.youtube.com/watch?v=r8ALzUluyXM
- An other assembly guide: http://www.cardella.tk/2014/09/fpv250-quadcopter-build.html
Configure FCU: CC3D Atom
- Install OpenPilot GCS (install of openpilot fails but openpilotgcs is working) https://wiki.openpilot.org/display/WIKI/Downloading+and+Installing+the+Ground+Control+Station
- Hardware setup: https://wiki.openpilot.org/display/WIKI/CopterControl+-+CC3D+-+Atom+Hardware+Setup
- Full introduction to building a quad with the CC3D https://www.youtube.com/playlist?list=PLYsWjANuAm4r-E61stLchCR4bzY3NmDNh
Batteries
- https://www.reddit.com/r/Multicopter/wiki/power
- LiPo are dangerous! https://www.youtube.com/watch?v=YCWdnjLqVWw
- C rating : the higher, the higher current you can draw http://www.rcheliwiki.com/C_rating
- C*Capacity in Ah=Current
- Current: 20C * 2.2Ah = 44A
- Power: 44A * 11.1V = 488.4W
- S is the number of cells in series, and is representing the tension (1S=3.7V, 2S=7.4, 3S=11.1V, ...). P is in parallel. Usually LiPo are in series and P=1
- Balancing: Cells need to be a the same charge level so we can avoid overcharging.
- It's a good idea to always use the balance mode to charge a multiple cells battery
- http://www.rcheliwiki.com/Balance_charger
- Use the charger to check and rebalance cells https://www.youtube.com/watch?v=AChoy_PsVEg
- A good trick to test is to charge the cells individually using the balance cable, it's much faster than the balance mode that needs to discharge overcharged cells a lot
Transmission
- Having some problems with the vTX right now, apparently at full throttle. Electrical perturbations ?
Gallery
- 1st flight https://www.youtube.com/watch?v=RCSfAMZ6bm0
- FPV Camera setup https://www.youtube.com/watch?v=aNmkK1-EYYc
cabling is hard
1st build
fpv tests
stats
rebuilt everything, better antenna placement, battery cables, fix the feet, ...
