* Building a FPV Drone: [http://www.hobbyking.com/hobbyking/store/uh_viewitem.asp?idproduct=52863 HobbyKing Spec Class 250fpv]
== Current setup ==
* [http://www.ecalc.ch/xcoptercalc.php?ecalc&lang=en&cooling=medium&rotornumber=4&config=flat&frame=250&tiltlimit=90&weight=500515&calc=auw&elevation=500&airtemp=25&qnh=1013&batteries=0&battcap=22001300&battri=0.0107&battv=3.7&battccont=3035&battcmax=4060&battweight=4438.6&chargestate=0&s=3&p=1&esc=0&esccont=12&escmax=12&escri=0.015&escweight=10&motor=0dys&type=0&motorkv=1900&motorio=0.5&motorvio=11.1&motorlimit=49&motorlimittype=w&motorri=0.405&motorlength=16&motorpoles=12&motorweight=15.578%7Cbe1806-2300&gear=1&propeller=0&pconst=1.313&tconst=1.0&proptwist=0&diameter=5&pitch=3&blades=2 &project=Quad250 Power calculator][[File:drone5.png|200px]]* MotorFrame: [http://hobbykingfpvracing.comch/hobbykingen/storeframes/__66414__Turnigy_Multistar_1704_1900Kv_12_Pole_Multi_Rotor_Outrunner_V2213-nighthawk-250-pro-v2-cf-frame-red.html?strSearch=1704%201900 4.4A max, 2-3s lipo, max 49WNighthawk 250 Pro V2 CF]
* ESC: [http://hobbyking.com/hobbyking/store/__55241__Afro_ESC_12Amp_Ultra_Lite_Multi_rotor_Motor_Speed_Controller_SimonK_Firmware_Version_3.html Afro 12A SimonK (2-4s lipo), BEC: 0.5A Linear 5.0v]
* Motor: [http://www.banggood.com/DYS-BE1806-2300KV-Brushless-Motor-2-3S-for-Mini-Multicopters-p-933192.html DYS BE1806 2300KV]* Props:** 2 blades: [http://fpvracing.ch/en/propellers/255-gemfan-5030-abs-propellers-one-pair-cw-ccw-black.html Gemfan 5030]** 3 blades (unused): [http://hobbyking.com/hobbyking/store/__23462__5030_green_Three_Blade_Propeller_CCW_ABS_3pc_.html Gemfan 5030]* <s>FCU: CC3D Atom Evo 4.8-15V 70mA</s> -> NAZE32* Batteries** 11.1V : Lots of 1300mAh 30-60C 3S 1800mAh 20C** 11[http://www.1V 3S 1000mAh 20C** 11hobbyking.1V 3S 2200mAh 30C ** 14com/hobbyking/store/__65997__Skyzone_Plug_N_Play_FPV_200_Set_With_TS5823_TX_RC832_RX_Sony_CCD_and_Circular_Polarized_Antennas.8V 4S 1800mAh 25C (non usable with these motors)html FPV]** FPV Camera: 1/3 Sony CCD 7-13V (3S) current 70mA** FPV Transmitter: 7-24V 190mA[http://www.hobbyking.com/hobbyking/store/uploads/808882987X53414X25.pdf manual] -> FR1 CH8** Video Receiver: current 12V 200mA
* [http://www.hobbyking.com/hobbyking/store/__78125__Quanum_DIY_FPV_Goggle_V2_w_5_inch_LCD_Monitor_Kit_.html Video "goggles"]
* Weight:** Theorical weight: ~415g** Calculated weight: 560g515g w/ battery (60C)
=== Upgrade planning ===
* More powerfull motors ! 18g 88Props 5045* better frame** expensive 150$ http://www.8W minihquad.com/frames/blackout-mini-h-quad/** cheap 20$-40$*** fiber glass http://www.banggood.com/ZMR250-H250-250mm-Fiberglass-Mini-Quadcopter-Multicopter-Frame-Kit-p-933189.html*** carbon http://www.banggood.com/H250-ZMR250-250mm-Carbon-Fiber-Mini-Quadcopter-Multicopter-Frame-Kit-p-933185.html* Better FPV antennas, stock are shitty with Skyzone kit (according to comments on HK)* Motor: [http://fpvracing.ch/en/motors/6264-emax-mt1806-2280kv-cw.htmlEMAX MT2204 2300KV] 7.5A, 2-3s, max 90W === Old setup ===* next frame ;) Frame: [http://www.minihquadhobbyking.com/frameshobbyking/blackoutstore/uh_viewitem.asp?idproduct=52863 HobbyKing Spec Class 250fpv]* Motor: [http://hobbyking.com/hobbyking/store/__66414__Turnigy_Multistar_1704_1900Kv_12_Pole_Multi_Rotor_Outrunner_V2.html?strSearch=1704%201900 4.4A max, 2-mini3s lipo, max 49W]* FCU: CC3D Atom 4.8-h-quad/15V 70mA
== Assembly ==
* Hardware setup: https://wiki.openpilot.org/display/WIKI/CopterControl+-+CC3D+-+Atom+Hardware+Setup
* Full introduction to building a quad with the CC3D https://www.youtube.com/playlist?list=PLYsWjANuAm4r-E61stLchCR4bzY3NmDNh
* Flash CleanFlight is very easy, via USB: http://nathan.vertile.com/blog/2015/04/27/flash-cleanflight-on-cc3d/
=== Batteries ===
** Current: 20C * 2.2Ah = 44A
** Power: 44A * 11.1V = 488.4W
* S is the number of cellsin series, and is representing the tension (1S=3.7V, 2S=7.4, 3S=11.1V, ...). P is in parallel. Usually LiPo are in series and P=1
* Balancing: Cells need to be a the same charge level so we can avoid overcharging.
** It's a good idea to always use the balance mode to charge a multiple cells battery
** http://www.rcheliwiki.com/Balance_charger
** Use the charger to check and rebalance cells https://www.youtube.com/watch?v=AChoy_PsVEg
** A good trick to test is to charge the cells individually using the balance cable, it's much faster than the balance mode that needs to discharge overcharged cells a lot
=== Issue/Fix/WIP ===
* <s>Having some problems with the vTX right now, apparently at full throttle. Electrical perturbations ?</s> Good, got some new [http://fpvracing.ch/en/fpv-accessories/87-circular-polarized-58ghz-antenna.html? antennas]
* [http://blog.oscarliang.net/lc-filter-fpv/ What is LC Filter and How it improve FPV experience]
== Gallery ==
* 1st flight https://www.youtube.com/watch?v=RCSfAMZ6bm0
* FPV Camera setup https://www.youtube.com/watch?v=aNmkK1-EYYc== V1 Hobbking frame ===
<gallery>
File:drone1.jpg
File:drone2.jpg
File:drone3.jpg|cabling is hardFile:drone4.jpg|1st buildFile:drone5drone6.pngjpg|fpv testsFile:drone7.jpg|rebuilt everything, better antenna placement, battery cables, fix the feet, ...File:Broken arm 2015-08-02 19-32.jpg|Broken an arm trying to rollFile:Fixed arm 2015-08-02 19-33.jpg|Arm fixed using epoxy, flying well, we'll see if it handles vibrations and the next crash</gallery> === V2 Nighthawk CF ===<gallery>File:V2 with Nighthawk frame 2015-08-07 23-58.jpg|V2 because HK frame broke again after ~10 landings, CF frame, looks nice (not tested yet)File:August 2015 quad 2015-08-26 08-01.jpgFile:Nighthawk v2-1 top 2015-09-03 14-22.jpg|V2.1 Cleaner build, new motors, new VTX, new FCFile:Nighthawk v2-1 2015-09-03 14-21.jpg|V2.1
</gallery>
== See also ==
* [[Drone]]