Difference between revisions of "Proxmark3"

From Fixme.ch
Jump to: navigation, search
(Flash the Proxmark using a BusPirate)
(Information)
 
(8 intermediate revisions by the same user not shown)
Line 3: Line 3:
 
* http://www.proxmark.org/proxmark
 
* http://www.proxmark.org/proxmark
 
* http://code.google.com/p/proxmark3/wiki/Compiling
 
* http://code.google.com/p/proxmark3/wiki/Compiling
 
+
* DIY hf antenna
== Flash the Proxmark using a BusPirate ==
+
** https://code.google.com/p/proxmark3/wiki/Antennas
* Get OpenOCD and compile it for the BusPirate
+
** http://www.proxmark.org/files/Documents/Antennas/How%20to%20design%20a%2013.56%20MHz%20customized%20tag%20antenna.pdf
git clone git://openocd.git.sourceforge.net/gitroot/openocd/openocd
+
* https://www.brmlab.cz/project/freakcard
cd openocd
+
./configure --enable-buspirate --enable-maintainer-mode --disable-werror --disable-shared
+
make && sudo make install
+
* Build the proxmark roms (bootrom and fullimage), see below
+
* Wire the BusPirate to the Proxmark3
+
** Connect GND, TDO, TMS, TDI, TCK using these pinouts, respectively p3 and buspirate
+
[[Image:Ulink_arm20pin_proxmark.gif]]
+
[[Image:buspirate_serial_pinout_connections_by_sparkfun-800x392.png]]
+
* Connect to the bus pirate
+
wget https://raw.githubusercontent.com/hewittc/proxmark3lcd/master/tools/at91sam7s512-buspirate.cfg
+
openocd -f at91sam7s512-buspirate.cfg
+
* Connect and flash
+
nc localhost 4444
+
> halt
+
> flash erase_sector 0 0 15
+
> flash erase_sector 1 0 15
+
> flash write_image ../armsrc/obj/fullimage.elf
+
> flash write_image ../bootrom/obj/bootrom.elf
+
  
 
== Proxmark 3 client ==
 
== Proxmark 3 client ==
Line 44: Line 26:
 
  ./client/proxmark3
 
  ./client/proxmark3
 
* Use it as Mifare emulator, https://code.google.com/p/proxmark3/wiki/Mifare
 
* Use it as Mifare emulator, https://code.google.com/p/proxmark3/wiki/Mifare
 +
 +
== Flash the Proxmark using a BusPirate ==
 +
* Get OpenOCD and compile it for the BusPirate
 +
git clone git://openocd.git.sourceforge.net/gitroot/openocd/openocd
 +
cd openocd
 +
./configure --enable-buspirate --enable-maintainer-mode --disable-werror --disable-shared
 +
make && sudo make install
 +
* Build the proxmark roms (bootrom and fullimage), see above
 +
* Wire the BusPirate to the Proxmark3
 +
** Pin 20 is GND and the the closest to the center of the board
 +
** Connect GND, TDO, TMS, TDI, TCK using these pinouts, respectively p3 and buspirate
 +
[[Image:Ulink_arm20pin_proxmark.gif|x200px]]
 +
[[Image:buspirate_serial_pinout_connections_by_sparkfun-800x392.png|x200px]]
 +
* Connect to the bus pirate
 +
wget https://raw.githubusercontent.com/hewittc/proxmark3lcd/master/tools/at91sam7s512-buspirate.cfg
 +
openocd -f at91sam7s512-buspirate.cfg
 +
* Connect the p3 by USB
 +
* Connect to openocd and flash
 +
nc localhost 4444
 +
> halt
 +
> flash erase_sector 0 0 15
 +
> flash erase_sector 1 0 15
 +
> flash write_image /full/path/to/armsrc/obj/fullimage.elf
 +
> flash write_image /full/path/to/bootrom/obj/bootrom.elf
 +
* Wait and enjoy the P3
 +
 +
* References
 +
** http://umeahackerspace.se/2013/03/21/bus-pirate-saves-the-day-proxmark3-jtag-flashing/
 +
** http://michaldemin.wordpress.com/2010/02/27/how-to-buspirate-and-openocd/
  
 
== See Also ==
 
== See Also ==
 
* [[Bus_pirate]]
 
* [[Bus_pirate]]

Latest revision as of 17:15, 29 April 2014

Information

Proxmark 3 client

  • Build the client/bootloader:
sudo apt-get install build-essential libreadline5 libreadline-dev libusb-0.1-4 libusb-dev libqt4-dev perl pkg-config
cd /tmp
wget http://sourceforge.net/p/devkitpro/perlupdaters/ci/master/tree/devkitARMupdate.pl?format=raw -o devkit.pl
chmod devkit.pl
./devkit.pl
export DEVKITPRO=~/devkitPro
export DEVKITARM=${DEVKITPRO}/devkitARM
export PATH=$DEVKITARM/bin/:${PATH}
svn co http://proxmark3.googlecode.com/svn/trunk proxmark3-read-only
cd proxmark3-read-only
make
  • Plug the Proxmark
./client/proxmark3

Flash the Proxmark using a BusPirate

  • Get OpenOCD and compile it for the BusPirate
git clone git://openocd.git.sourceforge.net/gitroot/openocd/openocd
cd openocd
./configure --enable-buspirate --enable-maintainer-mode --disable-werror --disable-shared
make && sudo make install
  • Build the proxmark roms (bootrom and fullimage), see above
  • Wire the BusPirate to the Proxmark3
    • Pin 20 is GND and the the closest to the center of the board
    • Connect GND, TDO, TMS, TDI, TCK using these pinouts, respectively p3 and buspirate

Ulink arm20pin proxmark.gif Buspirate serial pinout connections by sparkfun-800x392.png

  • Connect to the bus pirate
wget https://raw.githubusercontent.com/hewittc/proxmark3lcd/master/tools/at91sam7s512-buspirate.cfg
openocd -f at91sam7s512-buspirate.cfg
  • Connect the p3 by USB
  • Connect to openocd and flash
nc localhost 4444
> halt
> flash erase_sector 0 0 15
> flash erase_sector 1 0 15
> flash write_image /full/path/to/armsrc/obj/fullimage.elf
> flash write_image /full/path/to/bootrom/obj/bootrom.elf
  • Wait and enjoy the P3

See Also