Difference between revisions of "Tron Restore"
From Fixme.ch
(→Controls) |
(→A faire) |
||
| Line 14: | Line 14: | ||
* Repeindre | * Repeindre | ||
* Coller de nouveaux autocollants | * Coller de nouveaux autocollants | ||
| − | * Brancher un pc engine (ou autre) sur l'écran | + | * <s>Brancher un pc engine (ou autre) sur l'écran</s> |
| − | * Interfacer un pc avec les commandes de jeu | + | * Interfacer un pc avec les commandes de jeu => fait partielement |
| − | * Faire marcher l'audio | + | * <s>Faire marcher l'audio</s> |
= Components = | = Components = | ||
Revision as of 02:05, 16 June 2011
The project code on Gitorious https://gitorious.org/tron-restore
Description
Remettre en état la borne d'arcarde de Tron
A faire
- Démonter la borne
- Nettoyer et poncer la borne
- Repeindre
- Coller de nouveaux autocollants
-
Brancher un pc engine (ou autre) sur l'écran - Interfacer un pc avec les commandes de jeu => fait partielement
-
Faire marcher l'audio
Components
- Page de référence (Killer List Of Videogames)
- Wells Gardner 19K4906
- PC Engine
- Autocollants originaux: http://www.arcadeoverlays.com/StoreFrontProfiles/deluxeSFshop.aspx?sfid=17232&c=0&search_text=tron&submit=GO
- Manette originale http://groovygamegear.com/webstore/index.php?main_page=product_info&products_id=319&zenid=6fa2e2c526f83c87ca941d4319b8dbdf
- Exemple de restauration: http://driph.com/words/tag/tron/
Moniteur
- Simulating the video out of the Tron board shows that it produces max 0.7V on a 75R output. This means that we should be able to use the VGA voltage levels directly without conversion.
- How to connect a PC to an arcade monitor.
- X11 Configuration
- Arcade VGA
- https://secure.wikimedia.org/wikipedia/en/wiki/VGA_connector
- Mire
To convince the video card that a monitor is present, you need a VGA dummy.
From [1]:
8.10) Building a 5 BNC cable
This is straightforward, if time consuming and tedious.
The five coaxial cables (75 ohm, RG59 typical) are wired as shown in the
table. The corresponding VGA connector pin numbers are in ().
Coax Center Coax Shield
--------------------------------------
Red Video (1) Red Return (6)
Green Video (2) Green Return (7)
Blue Video (3) Blue Return (8)
H Sync (13) Ground (5,10)
V Sync (14) Ground (5,10)
Tie pin 11 (ID0) to Ground to indicate a color monitor.
Leave pin 12 (ID1) open.
Make sure that the lengths of the cables are fairly well matched - to within
a couple of inches - to assure that the 3 color channels line up precisely.
(One foot of cable is about 1.5 to 2 ns of delay which is significant for
a 10 ns dot clock!).
Also note that you will lose your 'Plug-and-Play' capabilities without the
direct control connections to the monitor (or for monitors without these
features).
That's it!
You will wish that your fingers were about 10 times smaller than they are,
however. :-)
Controls
- http://www.usb.org/developers/devclass_docs/HID1_11.pdf
- http://www.usb.org/developers/devclass_docs/Hut1_12v2.pdf
- http://msdn.microsoft.com/en-us/windows/hardware/gg487464.aspx
- Desktop Page (0x1), Gampad (0x5), Hat switch.
Personnes interessées
- Fred, JB, Simon, François
